Home > Support > Content

maintenance of telehandlers

Sep 23, 2023

During the operation of telehandlers, due to the changes in the internal mechanism of the vehicle and the influence of various operating conditions in the outside world, the various mechanisms and parts of the vehicle will inevitably and gradually produce different degrees of looseness, wear and tear, mechanical damage, deformation and accumulation of dirt and dirt and so on, and will even be damaged or broken, and there will be a vehicle failure or accident. The technical condition of telehandlers is gradually changing with the prolongation of the usage time. In order to reduce the wear and tear of each part of the telehandler, prevent early damage and failure in operation, the maintenance of the car is a very important work. Only by grasping the law of changes in the technical condition of the vehicle, correctly checking, reasonably maintaining and timely repairing can we reduce the wear and tear of the machine parts, prevent the occurrence of vehicle breakdowns or accidents, and make the telehandlers operate normally and prolong their service life.

Maintenance of telehandlers-1

 

Main points as follows:

1. Cleaning dirt and mud from telehandlers, key components including: forks, generator starter, water tank and air filter.

2. Check the tightness of each part, focusing on: fork carrier brackets, lifting chain tensioning screws, wheel screws, wheel retaining pins, brakes and steering screws.

3. Check foot brakes, steering reliability and flexibility.

4. Check for leaks, focusing on: pipe joints, diesel fuel tank, oil tank, brake pump, lift cylinder, tipping cylinder, water tank, water pump, engine oil sump, torque converter, transmission, drive axle, main reducer, hydraulic steering, steering cylinder. Drain oil filter deposits.

5. Check thermostat for proper operation.

maintenance of telehandlers-2

6. Check that the multiway reversing valve, lift cylinder, tilt cylinder, steering cylinder, and gear pump are working properly. Check whether the transmission shift operation is normal.

7. Check and adjust the clearance between the brake pads on the hand and foot brakes.

8. Change the oil in the sump, check that the crankcase vent hose is in good condition, and clean the oil filter and diesel filter element. Check that the generator and starter motor are securely mounted, that the connectors are clean and secure, and that the carbon brushes and commutator are not worn.

9. Check the tightness of the fan belt.

10. Check whether the wheels are firmly mounted, whether the tyre pressure meets the requirements, and remove the debris embedded in the tyre tread. Check whether the diesel fuel inlet screen is clogged or damaged, clean or replace the screen.

11. Check whether the diesel fuel inlet screen is clogged or damaged, clean or replace the screen.

12. Clean all tanks, filters and pipework and check for corrosion or cracks. After cleaning, do not wipe with gauze or cloth with fibres.

13. Clean the torque converter and gearbox, check parts for wear and replace with new oil. Check driveshaft bearings and change direction of universal joint cross shafts if necessary.

14. Check tightness and oil leakage of all parts of the drive axle and clean air holes. Check main reducer, differential and wheel reducer, adjust axial clearance of bearings and add or replace lubricant.Disassemble, adjust and lubricate front and rear hubs and move half shafts.

15. Remove and clean the gear oil pump, taking care to check the gears, housing and bearings for wear. Disassemble the multi-way valve, check the clearance between the valve stem and the valve body, and do not disassemble the safety valve if not necessary.

16. Inspect the steering knuckle for damage or cracks, check the fit of the steering axle main pin to the steering knuckle, disassemble and inspect the longitudinal and transverse cross tie rod joints and steering arms for wear.

17. Remove tyres, rust-proof and paint wheels, check inner and outer tyres and pads, change position and inflate as required. Check connections and tightness of handbrake parts, adjust working travel of handbrake lever and foot brake pedal. Check batteries.

18. Clean the water tank and oil radiator.

maintenance of telehandlers-3

 

 

 

 

Send Inquiry
Contact Us
    • Request Call:
    •  

    • Manager Wang:+86 19953645362


    • Manager Liu:+86 18615089090

    •  

    • Manager Ma:+86 18765666828

    •  

    • Manager Wang:+86 13864698681